Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision | Next revision Both sides next revision | ||
public:resources:fab_sejong:assembly [2015/05/23 11:18] kimkj |
public:resources:fab_sejong:assembly [2015/05/23 11:23] kimkj |
||
---|---|---|---|
Line 96: | Line 96: | ||
3. 2번째에서 끼운 Shaft와 일직선으로 Tensioner Pulley를 끼운다.\\ | 3. 2번째에서 끼운 Shaft와 일직선으로 Tensioner Pulley를 끼운다.\\ | ||
4. 또다른 'tensioner side plate'을 반대쪽에 끼우고, pully를 향해 마주보게 bearing을 끼운 'Tensioner front plate'도 아랫부분에 끼우도록 한다.\\ | 4. 또다른 'tensioner side plate'을 반대쪽에 끼우고, pully를 향해 마주보게 bearing을 끼운 'Tensioner front plate'도 아랫부분에 끼우도록 한다.\\ | ||
- | {{:public:research:3d_fabrication:fabatsejong:y2-1.jpg|}}\\ | + | {{y2-1.jpg|}}\\ |
\\ | \\ | ||
\\ | \\ | ||
Line 103: | Line 103: | ||
\\ | \\ | ||
1. 아래 그림과 같이조립하기 전에 pully를 가진 Y축 모터를 bridge back plate나사로 고정하라.\\ | 1. 아래 그림과 같이조립하기 전에 pully를 가진 Y축 모터를 bridge back plate나사로 고정하라.\\ | ||
- | {{:public:research:3d_fabrication:fabatsejong:y3-1.jpg|}}\\ | + | {{y3-1.jpg|}}\\ |
2. 그림과 같이 bottom bridge plate을 고정하기 전에 bridge back plate에 bridge inner plate을 고정시켜라.\\ | 2. 그림과 같이 bottom bridge plate을 고정하기 전에 bridge back plate에 bridge inner plate을 고정시켜라.\\ | ||
- | {{:public:research:3d_fabrication:fabatsejong:y3-2.jpg|}}\\ | + | {{y3-2.jpg|}}\\ |
3. bridge back plate에 bottom bridge plate을 고정시킨다. | 3. bridge back plate에 bottom bridge plate을 고정시킨다. | ||
(아래 그림을 명확하게 하기 위해서 bridge inner plate을 보이지 않게 하였다.)\\ | (아래 그림을 명확하게 하기 위해서 bridge inner plate을 보이지 않게 하였다.)\\ | ||
- | {{:public:research:3d_fabrication:fabatsejong:y3-3.jpg|}}\\ | + | {{y3-3.jpg|}}\\ |
4. 왼쪽 bridge inner plate와 pully support plate를 부착한다.\\ | 4. 왼쪽 bridge inner plate와 pully support plate를 부착한다.\\ | ||
- | {{:public:research:3d_fabrication:fabatsejong:y3-4.jpg|}}\\ | + | {{y3-4.jpg|}}\\ |
5. Pulley supprot plate 위에 bearing에 4mm Shaft(쇠막대)를 끼워 넣어라.\\ | 5. Pulley supprot plate 위에 bearing에 4mm Shaft(쇠막대)를 끼워 넣어라.\\ | ||
6. Y 축 Pulley와 Bearing사이에 Shaft Collar를 넣어라.\\ | 6. Y 축 Pulley와 Bearing사이에 Shaft Collar를 넣어라.\\ | ||
- | {{:public:research:3d_fabrication:fabatsejong:y3-56.jpg|}}\\ | + | {{y3-56.jpg|}}\\ |
7. bridge inner plates와 bridge front plates를 붙여라.\\ | 7. bridge inner plates와 bridge front plates를 붙여라.\\ | ||
- | {{:public:research:3d_fabrication:fabatsejong:y3-7.jpg|}}\\ | + | {{y3-7.jpg|}}\\ |
8. bridge back와 front plates와 bridge side plates를 붙여라.\\ | 8. bridge back와 front plates와 bridge side plates를 붙여라.\\ | ||
- | {{:public:research:3d_fabrication:fabatsejong:y3-8.jpg|}}\\ | + | {{y3-8.jpg|}}\\ |
9.M4-Screw를 이용하여 bridge의 오른쪽부분에 Y 축 tensioner을 안정감 있게 고정 시켜라.\\ | 9.M4-Screw를 이용하여 bridge의 오른쪽부분에 Y 축 tensioner을 안정감 있게 고정 시켜라.\\ | ||
- | {{:public:research:3d_fabrication:fabatsejong:y3-9.jpg|}}\\ | + | {{y3-9.jpg|}}\\ |
10. M2-Screw를 이용하여 Bridge bottom plate에 4개의 Bridge Belt Clamps를 고정시켜라. | 10. M2-Screw를 이용하여 Bridge bottom plate에 4개의 Bridge Belt Clamps를 고정시켜라. | ||
Bridge Belt clamps : 2개 긴 구멍을 가진 것, 2개의 작은 구멍을 가진 것.\\ | Bridge Belt clamps : 2개 긴 구멍을 가진 것, 2개의 작은 구멍을 가진 것.\\ | ||
- | {{:public:research:3d_fabrication:fabatsejong:y3-10(1).jpg|}}\\ | + | {{y3-10(1).jpg|}}\\ |
**주사기 보조대 조립과정 | **주사기 보조대 조립과정 |